Noelia Brinker asked 2 months ago
How to Replace a Kia Sportage Replacement Key
The key on many Kia models has an electronic keyless entry system built into. The key functions like the remote control, and can be exchanged by a Kia dealer.
Key fobs may stop working due to a number of reasons, such as a dead battery, worn-out buttons signal interference, or water damage. Here are some suggestions to assist you in getting your 2012 kia rio key fob programming key fob that is a replacement for the sportage for good.
How do you replace the remote key or smart key?
The battery inside your Kia’s smart key will eventually have to be replaced, regardless of whether it is a remote key that starts with a push button or a normal metal key that does not contain transponder. This is especially in the event that your vehicle displays a message that indicates that the remote or smart key is not powered by the battery.
This is a relatively easy process. In order to replace the battery of the key fob remove the mechanical key from the slit on the back of the key fob. Next, break the cover. A small screw will be found inside the key fob that holds the battery in the correct position. Remove the old battery by unwinding the screw using the help of a small screwdriver. Install the new battery and close the gap on the key fob.
Test the key fob by pressing the lock or unlock buttons. If the doors unlock and lock according to your expectations, then you’re all set! You can now make use of your Kia’s hands-free lock/unlock feature whenever your fingers feel cold or you have to do some errands in Brandon.
Note: Certain keys may require to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key has to be reprogrammed, you must be aware of the key code number stamped on the tag of the key code and then record it in a safe location.
How do I replace the battery?
If the Kia key fob does not respond when you press the lock/unlock button, it is most likely that the battery is low. A low battery may also cause other issues such as the check engine light turning on or delayed cranking of the engine. It is fairly easy to replace key fob batteries using just a few simple tools.
Make sure you turn off your vehicle and shut all doors prior to starting. Locate the small metal or plastic piece that is on the bottom of your key fob and move it until a metal key slips out. This key can be placed inside the driver door handle to unlock your car.
To replace the key fob’s battery, take off the cover on the rear and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and orient the new one in a way that the “+” positive side faces you, and the “-” negative side is facing towards the fob’s electrical contacts made of metal. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or bending the contacts on the metal.
Once the new battery has been installed and the key fob is turned on, turn it off and then on in the ignition several times until the door locks. You can then test your Kia key fob to determine whether it’s functioning properly again.
How to replace a smart key
Depending on the model of the Kia soul locked Keys in car Sportage, you may have a standard key fob or a smart key. The difference is that the smart key is equipped with the small blade of a key in it, whereas the standard fob does not. Both types of key fobs are equipped with an internal battery that will eventually have to be replaced. This is a simple procedure which takes just two minutes.
Make sure to shut off your 2014 kia optima key fob programming and be on a flat well-lit and well-lit area before you begin. Keep in mind that the fob has small pieces that could fall in the event of a mishap.
The first step is to find the small release button that is located on the lower backside of your fob. This will either be an oval silver button or a rectangular slot. After pressing this button mechanical key blade, it will come out and you can then open the key fob.
Once you have the key fob open then you can take off the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. Once you’re done, your key fob should permit you to lock the vehicle, unlock it, and then start your vehicle even if it’s not running.
How do I replace the mechanical key
The Kia keyfob is a great convenience that lets us lock or unlock our car with just pressing one button. Like any other device there are issues with it at times. There are solutions to solve these issues and keep your key fobs working for many years.
A dead or low-quality battery is one of the most common problems. This can cause the device to cease working or work intermittently. If this is the case you should replace the battery with a new one.
If this does not resolve the problem, use a standard flathead screwdriver to wedge the fob’s casing made of plastic open. Be cautious not to damage any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a new one.
Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the fob to make sure it’s working as intended. Contact a dealer or a locksmith to resolve the problem when the fob still is not working. Make sure they make you an emergency key that functions across all door and trunk cylinders to avoid lockouts again.